Appliance Error Code Guide Codes, causes & fix order
Dishwashers · Bosch

Bosch Dishwasher Error Code E24 / E25

Both codes mean the water will not leave, but they are not the same fault: one is a blockage somewhere in the path, the other is the pump itself refusing to turn.

Checked against Bosch support documentation Updated 16 November 2026 8 min read

The short answer

  • E24 — the drain path is blocked. Water is in the tub and will not leave.
  • E25 — the drain pump is not operating, or its circuit has failed.
  • Do this first: scoop the water out, remove and clean the filter, check the sump and the non-return valve, then look at the drain hose and the sink spigot.
  • Do not confuse it with E15 — E15 is water in the base tray, a leak, not a blockage.

Two codes, one symptom

Bosch numbers its dishwasher codes by function, so neighbouring numbers can describe closely related faults. E24 and E25 both leave standing water in the tub, which is why owners treat them as one problem. They are not.

CodeWhat the control detectedWhat that means practically
E24The level did not fall during the drain windowSomething is blocking the path — filter, sump, valve, hose, spigot
E25The drain pump is not running as expectedPump motor, impeller or its supply
E15Water detected in the base trayA leak, not a blockage — see the E15 guide

Getting the water out

  1. Unplug the machine and turn off the water supply tap under the sink.
  2. Open the door and scoop the water into a bowl with a cup or sponge. The sump holds several litres.
  3. Pull out the lower basket and remove the filter assembly — the cylindrical micro-filter and the flat filter underneath.
  4. Sponge out the sump so you can see the bottom and the pump cover.

The check order

  1. Filter. Rinse both parts under a tap. Grease, broken glass and rice are the classic blockages; a filter that has not been cleaned in months is the most common cause of E24.
  2. Sump and pump cover. Remove the cover over the drain pump (usually a twist-lock) and look inside. Glass, a bottle cap or a piece of cutlery stops the impeller.
  3. Non-return valve. Inside the sump area, a small flap valve stops water flowing back. A valve stuck shut with debris blocks the drain; one stuck open lets dirty water return.
  4. Drain hose. Follow it from the machine to the sink spigot or standpipe. Look for a kink, a crush behind the cabinet, or a hose with a low loop that traps water.
  5. Sink spigot or disposal connection. If the hose connects to a spigot under the sink, check the spigot and the trap. A blocked spigot looks exactly like a blocked dishwasher.
  6. Pump operation. Start a drain cycle and listen. A hum with no flow is a jammed impeller; silence is an electrical fault and points at E25.
  7. Pump replacement. If the impeller is broken, the motor open, or the pump has supply and does not turn, replace the pump.
Unplug before reaching into the sump, and turn the water off. Broken glass is the most common injury in this job — wear gloves and use a torch rather than fingers to explore the sump. Never run the pump with the filter removed.

Narrowing it

ObservationPoints to
Water drains slowly but does drain, then code returnsPartial blockage in the hose or spigot
Water does not move at all, pump humsJammed impeller
Pump silent on drainElectrical fault, E25
Dirty water returns after drainingNon-return valve stuck open
Code appears mid-cycle, water in tubFilter or sump blockage
Water on the floor as wellLeak — read E15 instead

Parts

Filter assembly, non-return valve, drain pump and drain hose. Bosch pumps are model-specific in their mounting and connector; order by the full model number printed on the inner door edge or the side of the tub, and photograph the old pump before removing it.

Repair or replace

Cleaning is free and fixes most E24 cases. A drain pump is a moderate part and a reasonable repair on a machine that heats and washes properly. If the pump has failed on a dishwasher that is also leaking from the door or the sump, the combined work is the point to weigh a replacement — repair or replace covers that.

Frequently asked questions

Why does E24 keep coming back after cleaning the filter?

Because the filter was not the blockage. Check the non-return valve, the hose and the sink spigot; a spigot blocked with grease is common and is outside the machine.

Can I run a cycle with E24 showing?

No. The machine will not complete a drain, so the wash water stays and the next cycle starts dirty. Drain and clear it first.

Does E25 always mean a new pump?

Not always — a loose connector at the pump or a failed relay on the control can produce it. But the pump is the usual answer, and it is a straightforward part on most Bosch models.

Sources

  1. Bosch Home Appliances Support — dishwasher error code guidance for E24 and E25 and the filter cleaning procedure (bosch-home.com support sections), accessed 16 November 2026.
  2. Bosch service documentation on the drain pump circuit, non-return valve and level sensing.
  3. Editorial review against the parts trade: drain pump and non-return valve failure patterns.

General information only. Sump layout, filter design and pump access differ between Bosch series and markets. Unplug before interior work and wear gloves when clearing glass from a sump.