The short answer
- E09 — heating fault. Dishes come out cold and wet.
- E15 — water in the base tray: a leak, not a blockage.
- E17 — fill fault: the machine is not taking water in time.
- E22 — filter or flow-sensor fault on models that use it.
- E24 / E25 — drain blockage / drain pump not running.
- Reset: most models clear a code with a button combination; none of them fix the cause.
The code map
Bosch's numbering is broadly functional, and knowing the bands saves time even before you find the exact definition for your model:
| Code | System | What you notice | First check |
|---|---|---|---|
| E01 / E02 | Temperature sensor / NTC circuit | Cycle stops early, water temperature wrong | Sensor connector, sensor resistance |
| E09 | Heating | Dishes cold and wet; wash runs but never heats | Heater continuity, heater relay, temperature sensor |
| E15 | Leak detection (base float) | Machine stops, water in the base tray | Door seal, internal hoses, pump seals |
| E17 | Fill / water inlet | No water, or the fill times out | Tap, inlet hose, inlet filter screen, water valve |
| E22 | Filter / flow sensor | Poor wash results, code after a few minutes | Filter assembly, flow sensor on models fitted with one |
| E24 | Drain path blocked | Standing water in the tub | Filter, sump, non-return valve, hose, spigot |
| E25 | Drain pump | Standing water, pump silent | Pump impeller, connector, pump supply |
| E27 | Supply voltage / power module | Machine dead or stopping randomly | Socket and supply; then power module |
Not every Bosch series uses every code, and the flexible-zone and fully integrated ranges add functions that older platforms did not have. The list above covers the codes owners actually meet; the model's own booklet or the rating-plate model number on Bosch's support site gives the definitive list.
Reading the code by group
Cold and wet dishes: the heating group
E09 and the sensor codes are the reason a dishwasher "works" but leaves the load cold and dripping. The heater is a simple resistive element; the usual failures are the element itself, its relay on the control, or a temperature sensor reading that stops the control from calling for heat.
No water: the fill group
E17 is the fill timeout. Check the tap under the sink first — it is turned off more often than anyone admits — then the inlet hose, the small mesh filter at the inlet valve, and the valve itself. Low mains pressure produces the same code as a blockage.
Water that will not leave: the drain group
E24 is a blockage and E25 is the pump. Clean the filter and the sump, check the non-return valve, then look outside the machine at the hose and the sink spigot. Only then suspect the pump.
Water where it should not be: E15
E15 is the only code in the list that is almost always telling the truth about something else. The float in the base tray lifts because water reached it, and the job is to find the leak — door seal, internal hose, inlet valve, sump or pump seals.
Everything electrical: E27 and the module codes
Supply faults look dramatic and are often boring: a socket on a shared circuit, an extension lead, a voltage dip when a large appliance starts. Check the supply before authorising a power module.
Resetting a Bosch code
Most Bosch dishwashers clear a displayed code with a reset sequence — often holding the start button for a few seconds, or a two-button combination — and some clear it when the door is opened and closed after power is restored. The sequence is in the manual for your series.
What a reset does not do is fix anything. If the code was caused by a leak, a blockage or a heating fault, it returns — usually in the same part of the same cycle, which is itself useful information.
Repair or replace
Filters, hoses and door seals are cheap. Heaters, pumps and sensors are moderate. A control module is the expensive end and only worth it on a machine that is otherwise sound and modern. Repair or replace puts the decision in numbers you can check against your own quote.
Frequently asked questions
Are Bosch codes the same across Series 2, 4, 6 and 8?
Mostly, for the core functions — heating, filling, draining and leaks. The higher series add functions and can show codes the entry series never displays.
The display shows a code and a letter as well — what is that?
Some models show a code with an additional letter or a flashing symbol indicating the phase (fill, wash, drain). The number is the fault; the extra character tells you where in the cycle it happened.
Do I need the model number to order a part?
Yes. It is printed on the inner edge of the door or on the side of the tub, in a format like SMs or SMS followed by digits. Bosch spares are matched to that number, not to the marketing name.
Sources
- Bosch Home Appliances Support — dishwasher error code guidance and manuals by model number (bosch-home.com support sections), accessed 16 November 2026.
- Bosch service documentation on fill, drain, heating and leak-detection circuits.
- Editorial review against the parts trade: the codes seen most often in service and the parts that resolve them.
General information only. Codes, access panels and part locations differ between Bosch series and markets. Confirm against your model's documentation, unplug before interior work, and leave power-module and hard-wired work to a qualified technician.