Appliance Error Code Guide Codes, causes & fix order
Washers · Samsung

Samsung Washer Error Code 5E / 5C

The wash finished, the drum is still full, and the machine will not spin or open. 5E and 5C mean one thing: the drain step ran out of time with water still in the drum.

Checked against Samsung support documentation Updated 16 November 2026 9 min read

The short answer

  • 5E / 5C — the drain cycle timed out. Water is still in the drum, so the spin and the door release are held back.
  • Most common cause: the pump filter is blocked by lint, hair, coins or a sock; second is a kinked or squashed drain hose.
  • Do this first: drain the drum through the emergency hose, open the round filter cover at the bottom front, clean the filter and check the impeller behind it turns freely.
  • If the filter is clean: check the hose run and the standpipe height, then test the pump. The pressure switch is the last suspect, not the first.

What 5E is actually reporting

During a drain, the board runs the drain pump and watches the water-level sensor. If the level has not fallen to the "empty" threshold by the end of the drain window — typically a few minutes, longer on some cycles — the programme stops and shows 5E. 5C is the same condition on displays that use a C instead of an E.

That means 5E is a timeout, not a pump verdict. Anything that slows the water down produces it:

  • A restriction before the pump (filter, sump, coin trap).
  • A restriction after the pump (kinked hose, blocked standpipe, a drain spigot blocked under the sink).
  • A pump that turns but cannot move water (worn impeller, debris wrapped around it).
  • A pump that does not turn at all (seized, open coil, no supply).
  • A sensor that reports water when the drum is empty (pressure tube holding water, blocked chamber).

The last one is worth remembering: an owner can empty the drum completely, run the machine, and still get 5E within seconds. That is not a pump failing to pump — that is the machine believing it is full.

Get the water out first, safely

You cannot diagnose a drain fault with a full drum, and on a front loader the door will not unlock while the level is high.

  1. Unplug the machine and wait a few minutes for the door lock to release.
  2. Put towels and a shallow tray in front of the filter cover at the bottom right (most Samsung front loaders).
  3. Pull out the small emergency drain hose, remove its cap, and let the water run into the tray. Cap it, empty the tray, repeat. Expect several litres.
  4. Then unscrew the filter cover — turn slowly, because more water will follow — and pull the filter out.
Unplug first, and never run the pump with the filter removed. Water and lint will spray from the housing; the impeller is exposed and can injure a finger. Keep the machine on a dry floor and do not tip a front loader onto its side while it holds water.

The check order

  1. Filter. Rinse it under a tap and look into the housing with a torch. Coins, bra wires, hair clips and children's socks are routine. This clears the majority of 5E faults.
  2. Impeller. Reach into the housing and turn the impeller with a finger. It should rotate with light resistance and no grinding. A jammed impeller is often a small object you can hook out with a bent wire.
  3. Drain hose. Pull the machine out and follow the hose to the standpipe or spigot. Look for a kink behind the machine, a hose pushed flat against the wall, a crushed section under the machine, or a hose that loops up higher than the manufacturer allows before dropping.
  4. Standpipe and trap. If the hose discharges into a standpipe, check it is not blocked with lint — a plugged standpipe backs water up and looks exactly like a failing pump. On a sink spigot, check the spigot and the trap below it.
  5. Pump running? Start a drain or spin cycle with the filter fitted and listen at the bottom of the machine. Silence means an electrical fault (coil, connector, board); noise with no flow means a mechanical one (impeller, restriction).
  6. Pressure tube and switch. If the drum is empty and 5E appears within seconds, disconnect the pressure tube at the switch, check it for trapped water and clean the chamber port. Refit and test.
  7. Filter housing seal. A filter cover that was refitted crooked or without its O-ring leaks air, and the pump then cannot prime. Check for a drip after reassembly.

Which part each check points to

PartSignature of failureAction
Pump filterLint mat, coins, a sock, a hair clipClean; replace only if cracked
Drain hoseKink, crush, split, incorrect loop heightReroute or replace
Drain pumpImpeller jammed or broken, coil open, silent on a drain cycleClear or replace
Pressure tube / chamberWater trapped in the tube, residue blocking the portClean and refit
Water-level switchEmpty drum reported as fullReplace
Main boardNo supply to a known-good pumpReplace — last resort

Samsung uses several pump families across its front-load platforms, and they are not interchangeable. Order by the full model code from the rating plate inside the door opening, and compare the mounting lugs and connector in the photo before you pay.

Why it comes back

5E has a habit of returning every few months on machines that are used the same way. Three habits cause it, and all three are free to change:

  • Washing with pockets full. Tissues dissolve into lint that packs the filter; coins and clips jam the impeller.
  • Too much detergent. Excess suds slow the drain and leave a soap film in the filter housing that traps lint.
  • Never cleaning the filter. Samsung recommends checking it regularly — monthly is realistic in a busy household — and the filter is designed to be reached without tools.

Repair or replace

A cleaned filter or rerouted hose costs nothing but an hour. A drain pump is a modest single part on most machines and normally worth replacing on a washer that is otherwise healthy. If the fault has taken the board with it, or the machine also shows bearing noise or a leaking tub seal, the comparison in repair or replace is the right frame, and what a washer repair involves explains which parts of a quote you can influence.

Frequently asked questions

Can I use the machine with 5E if I bail the water out by hand?

No. The machine will not spin with water it cannot remove, and forcing a spin with a full drum can damage the bearings and the suspension. Fix the drain path first.

Why does 5E appear only on some cycles?

Because drain time is programme-dependent. A gentle cycle with a slow final drain, or a cycle that drains through a different path, can finish inside the window where a normal cycle times out. A partial restriction behaves exactly like this.

The filter was clean — is it definitely the pump?

Not until the hose and the standpipe are checked too. A blocked standpipe or a hose with an incorrect high loop are both common and both look like a dead pump from the display.

Is 5C different from 5E?

No — same drain timeout, different letter on the display. Samsung has used both across model years and regions.

Sources

  1. Samsung Support — washing machine error code guidance for 5E and 5C, and the drain filter cleaning procedure (samsung.com support sections), accessed 16 November 2026.
  2. Samsung service documentation for drain timing and the water-level switch circuit.
  3. Editorial review against the parts trade: drain pump and filter failure patterns on Samsung front-load and top-load platforms.

General information only. Drain timing, filter location and pump type vary by model and market. Confirm against your machine's documentation, unplug before opening the filter housing, and have a qualified technician handle anything involving mains wiring.