The short answer
- Most likely first: the pump filter is blocked, or the drain hose is kinked or pushed too deep into a sealed standpipe.
- Second: the pump is jammed by an object, or the standpipe itself is blocked.
- Less common: a lid or door switch stopping the cycle, a pressure switch that will not confirm an empty drum, a blocked pump housing, a failed pump, a control fault.
- Before anything: unplug, then get the water out through the emergency drain or by siphoning the hose.
Why there is no code
Codes are raised on timeouts, not on symptoms. A machine that drains slowly but finishes, or that has stopped earlier in the cycle for a different reason, leaves water in the drum without ever reaching the point where a drain fault is declared. Owners then describe it as "it will not drain" when the machine has not actually tried yet.
So the first question is not which part failed, but where the cycle stopped:
| Where it stopped | What it suggests |
|---|---|
| Straight after filling | Not a drain fault — likely a fill or level-sensing issue |
| Mid-wash, drum full and quiet | Door/lid switch, motor fault, or a power interruption |
| At the drain, pump humming | Restriction or jammed pump |
| At the drain, pump silent | No supply to the pump: connector, coil, or control |
| After the drain, water reappears | Backflow — hose too low, or a shared drain pulling water back |
First: get the water out
- Unplug the machine. On a front loader the door lock releases when power is removed, after a short delay.
- Front loader: open the small service flap at the bottom front, pull out the emergency drain hose, remove its cap over a shallow tray, and drain in stages.
- Top loader: take the drain hose off its standpipe, lower the end into a bucket below the drum, and let it siphon. You may need to raise and lower the hose a few times to restart the siphon.
- Never tip a front loader onto its side with water in the drum: the water will reach the motor and the electronics.
The seven causes, in order
1. The pump filter is blocked
Lint, hair, coins, bra wires and small garments collect in the filter and slow the pump to a trickle. This is the single most common cause and the cheapest to fix. Clean it, check the housing for objects, and turn the impeller by hand.
2. The drain hose is kinked or badly routed
Pull the machine out and follow the hose. A hose folded behind the cabinet, crushed under the machine, or pushed so far into a standpipe that it seals against the pipe will not drain. There must be an air gap at the discharge.
3. The standpipe or sink spigot is blocked
If the drain it discharges into is blocked, the water has nowhere to go and comes back. This is common on a sink spigot with a blocked trap, and on a standpipe that has collected lint for years. Test by discharging into a bucket.
4. Something is jamming the pump impeller
A small object can pass the filter and jam the impeller. The pump hums but does not turn, or turns with a scraping. With the machine unplugged, reach into the housing and free it — a bent wire or long-nose pliers works better than fingers.
5. The lid or door switch is stopping the cycle
On a top loader, a lid switch that fails open leaves the machine unable to spin or drain. On a front loader, a door lock that does not report locked does the same. If the machine stops with a full drum and no drain attempt, this is worth checking before the pump.
6. The pressure switch will not confirm an empty drum
A blocked pressure hose or chamber can hold the switch in the "full" position, so the machine never believes the drain worked. The pump may be fine. Clean the tube and the chamber port.
7. The pump, or the control, has failed
Only after the six above: a pump with an open coil or a seized bearing, or a board that does not energise the pump. A pump is a modest part; a board is the point where the repair competes with a new machine.
Matching the cause to the fix
| Test result | Cause | Fix |
|---|---|---|
| Water flows freely into a bucket from the hose | Discharge point blocked | Clear standpipe or trap |
| No flow, impeller turns by hand | Restriction before pump, or air lock | Clean filter, check filter seal |
| No flow, impeller jammed | Object in pump | Clear the object |
| Pump silent on a drain cycle | Electrical fault | Test coil, connector, control |
| Drum empty, machine still "full" | Pressure switch or tube | Clean tube and chamber |
| Machine stops before draining at all | Lid or door switch | Test and replace switch or lock |
Why it comes back
- Pockets. Tissues dissolve into lint that packs the filter within weeks.
- Too much detergent. Foam slows the drain and leaves a film that traps lint.
- No routine. A filter check once a month is the whole maintenance schedule for most machines.
- Wrong hose routing after a kitchen or laundry renovation — very common, and invisible until the next wash.
Repair or replace
Causes one to three cost nothing. A pump is a modest repair and worth doing. A board fault on an older machine is where repair or replace earns its place, and what a washer repair involves explains why two quotes for the same pump differ.
Frequently asked questions
Is it safe to leave water in the drum overnight?
It will not flood, but standing water in a drum is hard on the seal and the bearings and starts to smell. Drain it the same day if you can.
The door will not open — how do I get the washing out?
Drain the drum first, then unplug and wait. Most front loaders have a manual release near the filter housing or a cord behind the lower panel; the manual for your model shows where.
Can a blocked filter cause a smell as well?
Yes. A filter holding lint and water is the main source of a sour smell in a front loader. Cleaning it is usually the whole fix.
Sources
- Manufacturer support documentation for drain faults and filter cleaning: Samsung, LG, Whirlpool and Bosch consumer support sections, accessed 16 November 2026.
- Service documentation on drain timing, pump circuits and pressure switch behaviour across front-load and top-load platforms.
- Editorial review against the parts trade: the failure order of the drain path in machines seen in service.
General information only. Layouts differ between front-load and top-load machines and between brands. Unplug before opening any panel, and have a qualified technician handle mains wiring or a pump you cannot reach safely.