Appliance Error Code Guide Codes, causes & fix order
Washers · Samsung

Samsung Washer Error Code 4E / 4C

The drum turns, the cycle light blinks, and the machine stops before the clothes are wet. 4E and 4C both mean the same thing: the washer expected water, and its level sensor never saw it arrive.

Checked against Samsung support documentation Updated 16 November 2026 9 min read

The short answer

  • 4E / 4C — the fill cycle timed out. The machine opened the inlet, waited, and never reached the water level for that step.
  • Most common cause: a closed or part-closed tap, a kinked fill hose, or a mesh filter at the back of the machine packed with grit.
  • Do this first: check both taps are fully open, straighten the hoses, then unscrew each hose from the machine and clean the small mesh screen inside the inlet.
  • If water flows freely and the code returns: the inlet valve, the pressure hose or the level sensor is next — in that order, and never all three at once.

What 4E is actually reporting

A Samsung washer does not have a flow meter. It fills for a set time, then checks the water-level sensor — a pressure switch fed by a thin air tube from the bottom of the drum. When the air pressure in that tube does not rise as the drum fills, the board concludes the water never arrived, stops the cycle, and shows 4E.

That single design detail explains most of what owners find confusing about this code:

  • The machine cannot tell the difference between no water and water it cannot measure. A blocked pressure tube produces exactly the same 4E as a closed tap.
  • It cannot tell the difference between low pressure and no pressure. A trickling supply fills the drum eventually, but not inside the time window.
  • It reports the fill step, not the wash step — so 4E almost always appears early in a cycle, before the drum has water in it.

Across Samsung's consumer ranges — eco bubble, AddWash, QuickDrive, and the top-loaders sold as WA and WA-E series — the code has been printed as 4E, 4E1, 4E2 and, on displays that use letters differently, 4C. The number refers to the same fill-timeout logic. A separate variant, 4C2, appears on models with an automatic temperature fill and points at the temperature sensor side of the same step.

Which version of the code you have

Before you start pulling hoses, note two things: whether the machine fills at all, and whether the failure is on hot or cold.

What you seeWhat it suggestsWhere to look
No water enters the drum at allSupply is closed or blocked upstream of the valveTaps, hoses, inlet mesh screens
Water enters slowly, then the code appearsLow pressure or a partly blocked screenMesh screens, supply pressure, another tap on the same line
Drum fills, then code appears immediatelyThe level sensor is not reading the waterPressure tube, pressure chamber, level sensor
Fills on hot but not cold (or the reverse)One side of the inlet valve or its screenThat side's hose and inlet filter
Code only in winter, on an outside wallFrozen hose or valve bodyHose run, insulation, ambient temperature
Unplug the machine before touching the inlet area, and close both water taps first. The inlet valve is live whenever the machine is plugged in, even with the panel switched off. If the machine is plumbed with a permanent connection rather than hoses, or you cannot reach the isolation valve, stop and call a plumber or technician.

The check order that finds it

  1. Both taps fully open. Not "open a bit" — fully. A washer tap that was closed for a repair and turned back only part-way is the single most common cause of 4E in homes where nothing else changed.
  2. Hoses: kinked, squashed, or with a filter washer inside. Pull the machine out and look at the whole run. A hose pushed hard against the wall folds shut. Some installations use a filter washer in the hose end as well as the machine screen, and that washer blocks first.
  3. Inlet mesh screens. Unscrew each hose from the back of the machine. Inside each inlet port is a small mesh cone; lift it out with pliers and rinse it. Grit after a municipal pipe repair is normal and takes two minutes to clear.
  4. Supply pressure. Open a nearby cold tap and watch the flow. If the house pressure is low — a gravity-fed tank, a shared line, a partially closed main — the machine may time out even with a clean path. Filling from a bucket is not a fix, but it confirms the diagnosis.
  5. The pressure tube and chamber. With the machine unplugged, find the thin transparent tube running from the pressure switch to a small chamber on the outer drum. Pull the tube off and check it for water, detergent residue or a split, and clean the chamber port. Clear it, refit it, and run a rinse: a clear that lasts is a blocked tube, not a failed valve.
  6. The inlet valve solenoids. Only now. With the machine unplugged but the taps open, listen and feel for the valve opening on a fill cycle, or measure the coil resistance on the two solenoids if you have a meter. A dead coil on one side produces 4E on the cycle that uses that side.
  7. Water-level sensor / pressure switch. If water clearly enters, the tube is clear and the code persists, the pressure switch is not reporting. This is a cheap part on most models but should be confirmed with a meter or by a technician, because a board fault can emulate it.

Which part each check points to

Nothing here needs a part number to think about — but if you do end up ordering, this is the list of parts a 4E can end in, in the order they are actually replaced.

PartWhat it doesSignature of a real failureReplace or clean
Inlet mesh screenFilters grit before the valveGrit or scale visible, water flow improves after rinsingClean; replace if torn
Fill hoseCarries water from the tapVisible kink, bulge or a perished rubber liningReplace
Inlet valve (dual or triple)Opens the water path on commandClean screens, good pressure, no water on a fill cycle; one side deadReplace
Pressure tube and chamberFeeds air pressure to the level switchTube blocked with residue, water trapped, or splitClean and refit; replace if split
Water-level sensor / pressure switchReports the level to the boardDrum fills, no reading; code straight after filling startsReplace
Main control boardDrives the valve and reads the sensorOnly after valve and sensor are proven goodReplace — last resort

For a parts search you need the full model code from the rating plate, not the marketing name. On Samsung front loaders it is usually on a sticker inside the door opening or on the back panel; on top loaders it is under the lid or on the rear panel. The model code and the code on the display together are what a parts counter needs.

Repair, replace, or leave it

Almost every 4E is a cleaning job, which is why it is worth an hour before any money. If you have worked through the order and found a dead valve solenoid, the repair is a single part on the back of the machine and is normally worth doing on any washer under about eight years old. If a technician finds a failed board on a machine that is already past its warranty and showing other faults, the comparison in repair or replace is the honest next step — and what a repair actually involves explains why two quotes for the same valve differ.

Frequently asked questions

Does 4E damage the machine if I keep resetting it?

The code itself does no harm: the board stops the cycle to protect the heater, which must never run dry. What does harm is repeated dry heating if the fault is intermittent, and a valve that is stuck open, which can flood. Clear the cause rather than the message.

Why did 4E appear mid-cycle, after the wash had started?

Some cycles fill more than once — a rinse fill, or a top-up after the load absorbs water. A machine that fills for the wash and faults at the rinse is failing on the same path, usually a partly blocked screen or a pressure tube that reads high until it is full of water.

Can a blocked filter inside the machine cause 4E?

Not the drain filter — that produces 5E. A blocked drain filter can, however, leave water in the drum from the previous cycle, which changes the level reading at the start of the next one. If 4E and 5E alternate, clean the drain filter first and then re-test.

Is 4C the same as 4E?

On the displays that use it, yes: 4C is the same fill-timeout condition written with a C. Samsung has printed both forms across model years and regions. Treat them identically, and treat 4C2 as the temperature-related variant of the same fill step.

Sources

  1. Samsung Support — washing machine error code guidance for 4E, 4C and 4C2 (samsung.com support sections for US, UK and EU markets), accessed 16 November 2026.
  2. Samsung service documentation for the fill cycle: inlet valve timing, water-level switch and pressure chamber description.
  3. Editorial review against the parts trade: fill valve and pressure switch failure patterns across Samsung front-load and top-load platforms.

General information only. Fill logic, code letters and part locations differ between model years and markets. Confirm the code and the model against your machine's documentation, unplug before opening any panel, and have a qualified technician handle anything involving mains wiring or a permanent plumbing connection.