Appliance Error Code Guide Codes, causes & fix order
Washers · Samsung

Samsung Washer Error Code UE / Ub

The spin starts, the drum thumps, the machine stops and shows UE. It is the code owners learn to ignore — until the machine starts walking across the floor.

Checked against Samsung support documentation Updated 16 November 2026 8 min read

The short answer

  • UE / Ub — the load would not balance for the spin, so the machine refused to spin fast.
  • Most common cause: the load itself — one heavy item, one duvet, a wash of only towels — or a machine that is not sitting level.
  • Do this first: open the door, separate the load by hand, add a couple of smaller items, and check the machine does not rock on its feet.
  • If it happens with every load: test the suspension by pressing each corner of the drum, then look at the level sensor and the drum bearing. That is a different repair.

What UE is reporting

Before a spin, a Samsung washer tumbles slowly to spread the load, then measures how much the drum is off centre — on most platforms by watching the motor's current draw and the speed ripple, with a level sensor confirming the drum's position. If the imbalance is too large, it retries a few times, then stops with UE instead of spinning a heavy load off its axis.

That is a protective decision, not a failure. A drum spinning at 1,200 rpm with a 5 kg lump on one side will destroy its bearings and can crack the outer tub. The machine is telling you it would rather stop than do that. Ub is the same condition written with a lower-case b on displays that use it.

The load causes, which are most of them

LoadWhy it will not balanceWhat to do
One duvet, blanket or sleeping bagIt balls up on one side and holds water unevenlyUse a low-spin bedding cycle; add two towels so the load redistributes
One heavy item (bath mat, jeans, a rug)Mass sits in one place with nothing to counterbalance itWash with two or three lighter items
Very small loadToo little mass for the sensor to read a stable distributionAdd items, or use a half-load cycle
Waterlogged foam or memory foam pillowTraps water and never distributesDo not machine wash; hand wash and press
Machine not level / feet not lockedThe whole cabinet moves with the drumLevel front to back and side to side, lock the feet

If UE appears once a month on a bedding wash and never otherwise, there is nothing wrong with the machine. If it appears on a normal mixed load, move to the mechanical checks below.

Mechanical checks, in order

  1. Level and stability. With the machine empty, push the top corner diagonally. A cabinet that rocks means a foot is not touching the floor or the locknuts are loose. Correct the feet before anything else — this alone fixes a surprising share of repeat UE faults.
  2. Suspension (front loaders). Open the door and press down firmly on the drum's top edge, then release. It should return with one small bounce. A drum that keeps oscillating, or that sinks easily, has worn springs or dampers. Check all four.
  3. Drum bearing and spider. Lift the drum at the door opening and feel for movement, then rotate it by hand and listen. A metallic knock, a grinding rumble or visible rust streaks from the door seal point at the bearing or the aluminium spider — an expensive fault that often ends the machine's life.
  4. Foreign object in the drum. A bra wire or a coin between the drums can create a heavy spot and a scraping noise. Look through the door with a torch, and check the drum paddles for a loose fitting.
  5. Level sensor. The drum-position sensor is a small part on top of the tub on many Samsung models. If the wires are chafed, the connector is wet, or the sensor is failing, UE can appear on a perfectly balanced load. This is a diagnostic for a technician with live data.
  6. Motor and board. Least likely. A motor that surges, or a board that misreads current, produces imbalance reports that do not match what the drum is doing.
Unplug before reaching into the drum or lifting the machine. A washer with a heavy unbalanced load can also be physically unstable: do not try to stop a spinning drum by hand, and never open the door mid-spin on a machine that has not unlocked.

What it points to

PartWhen it is the answerWeight of the repair
Feet / locknutsCabinet rocks; machine walksFree adjustment
Suspension springs and dampersDrum bounces more than once; sags on one sideModerate, four parts
Drum bearing / spiderMetallic knock, rumble, rust streaksHeavy — often not economic
Level sensorBalanced load still reports imbalanceSmall part, technician diagnosis
Door seal / paddleTorn seal, loose paddle causing a thumpModest

Repair or replace

If the cause is a load or a levelling foot, there is nothing to buy. If the suspension is worn, the repair is worth doing on a machine that is otherwise quiet and dry. If the bearing or spider has failed, the labour is the whole cost and the decision usually turns on age — the same comparison as in repair or replace.

Frequently asked questions

Why does the machine spin fine sometimes and fail others?

Because imbalance is a property of the load, not the machine. A mixed load distributes; a single heavy item does not. The fault is intermittent by design.

Can I just keep restarting until it spins?

You can, and it sometimes works because a restart redistributes the load. If it takes several attempts on every wash, the load habit or the suspension needs attention rather than the button.

Is Ub the same fault as UE?

Yes. Samsung has printed both forms; the meaning is unchanged.

The machine moved across the floor — is that UE damage?

It is a sign the feet were not locked and the drum was allowed to walk. Check the feet, then check for a damaged levelling foot or a bent cabinet before running another heavy load.

Sources

  1. Samsung Support — washing machine error code guidance for UE and Ub, including load advice for bedding (samsung.com support sections), accessed 16 November 2026.
  2. Samsung service documentation on the spin distribution step and the drum-position sensor.
  3. Editorial review against the parts trade: suspension, bearing and spider failure patterns on Samsung front loaders.

General information only. Sensor type, suspension design and drum construction vary between models. Confirm the code against your machine's documentation, unplug before internal checks, and leave bearing or tub work to a qualified technician.