The short answer
- LE — either a leak detected in the base of the machine, or a water-level fault, depending on model. Look for water first: that decides which it is.
- LC — the water-level sensing circuit: pressure switch, tube or chamber.
- Do this first: unplug, pull the machine out, and look and feel under it. Dry the floor, run a fill, and watch where the water appears.
- No water at all but the code returns: it is a sensing fault — clean the pressure tube and chamber before buying anything.
Two faults, one pair of letters
This is the code that causes the most misdiagnosis in the Samsung range, because the same two letters were used for two different things:
- Leak detection. Machines with a float switch in the base pan raise LE when water collects there. The machine stops because a leak plus electricity plus a spinning drum is the worst combination in the house.
- Water-level fault. On other platforms LE reports that the level reading is implausible — the drum fills without the switch registering, or the switch reports water that is not there.
LC is more specific: it points at the sensing circuit — the pressure switch, the thin tube running to the drum chamber, or the chamber port itself.
Step one: find out whether there is water
| What you find under the machine | Where to look | Typical cause |
|---|---|---|
| Water at the front edge, damp filter area | Pump filter cover and its O-ring | Filter refitted crooked or without a seal |
| Water at the front, below the door | Door seal, door glass lip | Torn seal, trapped lint, foaming from too much detergent |
| Water at the back, near the taps | Inlet hose connections, mesh holders | Loose hose, missing or perished washer |
| Water at the back, lower | Drain hose clamp, pump outlet | Loose clamp, split hose |
| Water only during draining | Drain path, standpipe joint | Restriction causing a backflow at a joint |
| Water always present, increasing with use | Tub seal / bearing area | Seal failure — a heavy repair |
A neat trick before you start: dry the floor thoroughly, put a sheet of kitchen paper under the machine, and run a short cycle. The paper tells you where the first drip lands, which is usually the joint nearest the fault.
If there is no water: the sensing circuit
- Pressure tube. With the machine unplugged, follow the thin clear tube from the pressure switch down to the chamber on the outer tub. Disconnect at the switch, look for water or detergent residue inside, and blow through it gently. A blocked tube reads as "full" or "empty" permanently.
- Chamber port. The small plastic chamber can clog with lint and detergent. Remove it, rinse it, and check that the port into the tub is clear.
- Tube fitment. A tube pushed on halfway, or a split end, leaks air pressure and gives erratic readings — usually an LE or LC after a repair, which is a useful clue.
- The switch. If the tube and chamber are clear, the switch itself is the remaining part. Test with a meter if you are comfortable doing so, or have it confirmed with live data.
- Board. Only after the switch has been proven good.
Resetting after a leak fault
A machine with a base-pan leak sensor will keep the fault latched until the base is dry and the machine is power-cycled. That is why owners sometimes clear it accidentally and then flood the floor: the code goes away when the water evaporates, not when the leak is fixed.
- Unplug and pull the machine out.
- Remove the base water — tilt carefully onto towels, or use a sponge through the front service opening where the model allows it.
- Find and fix the leak, then run a short cycle with paper underneath.
- Only then plug back in and clear the code with a power cycle.
Repair or replace
Filter seals, hose washers and a pressure tube are trivial. A door seal is a modest part and worth replacing. A tub seal or bearing replacement is a major strip-down: on a machine over about eight years old, the labour usually exceeds the value of the appliance, and repair or replace sets out how to judge that with your own numbers rather than ours.
Frequently asked questions
Can too much detergent cause LE?
Yes, indirectly. Excess foam pushes water past the door seal and can lift a base float. It also leaves residue in the pressure chamber that eventually produces LC. Use the dose on the bottle for your water hardness, not the largest dose printed.
Is it safe to use after the code clears?
Only if you found and fixed a cause. A code that cleared by itself on a dry floor may still come back, and an unfixed leak can damage the floor and the machine's electronics.
Does LE always mean the machine is scrap?
No. Most LE faults end at a filter seal, a hose joint or a door seal. It is the tub-seal and bearing failures that end a machine's life.
Sources
- Samsung Support — washing machine error code guidance for LE and LC (samsung.com support sections), accessed 16 November 2026.
- Samsung service documentation on the water-level switch, pressure chamber and base leak sensor.
- Editorial review against the parts trade: seal, hose and pressure-switch failure patterns.
General information only. Whether LE means a leak or a level fault depends on your model. Confirm against your machine's documentation, unplug before internal checks, and leave tub and bearing work to a qualified technician.