Appliance Error Code Guide Codes, causes & fix order
Refrigerators · Whirlpool

Whirlpool Refrigerator Error Codes

Whirlpool splits its codes into P (power), F (function) and E (electronic) families. A code like F6 E1 is read as two parts: the system that failed, then the specific fault inside it.

Checked against Whirlpool support documentation Updated 16 November 2026 9 min read

The short answer

  • PO — power interruption. The control restarted; it is a record, not a failed part.
  • F codes — a functional fault in a component circuit (fan, damper, heater).
  • E codes — a sensor or electronic fault (thermistor, communication).
  • Do this first: find the tech sheet behind the toe grille. It defines the codes for your exact platform, and the same letters mean different things on different Whirlpool families.

The grammar of a Whirlpool code

Whirlpool, like its sister brands Maytag, KitchenAid and Amana, writes codes in two parts: a component reference and a fault type. That is why you see pairs such as F6 E1 or F3 EC instead of a single number.

PrefixFamilyWhat it means in practice
PPowerThe supply or the control's power circuit was interrupted
FFunctionA component circuit did not behave as expected (fan, damper, heater, valve)
EElectronicA sensor reading or a communication path is invalid

Because the numbers are platform-specific, the same letters can describe different components on a side-by-side and on a French-door cabinet. The authoritative source is the tech sheet for your model — a folded sheet behind the toe grille or in a sleeve at the back.

The codes owners ask about most

CodeUsual meaningWhat you noticeFirst check
POPower interruptionDisplay flashing, cycle reset, temperatures recoveringSupply and breaker; clear and observe
F6 E1Component circuit fault (evaporator fan group on many platforms)Compartment warm, fan silent or iced inIce on the coil, fan connector
F3 ECDefrost / heater circuit fault on several platformsHeavy frost, warming every few daysDefrost heater continuity, sensor
F1 E1Thermistor / sensor circuit faultTemperature drifting, wrong readingsSensor connector and resistance
F2 E1Damper or airflow control faultOne compartment too warm or too coldDamper movement, ice in the air path

Treat this table as orientation, not as your machine's definition: confirm every code against the tech sheet or the manual's code page before ordering a part.

PO: the code that means nothing is broken

PO appears after a power cut, a tripped breaker, or a loose plug. The control reports that it restarted and lost its timing. Clear it, confirm both compartments return to temperature, and only investigate if it repeats — repeated PO usually means a marginal supply, a damaged cord or a failing control's power circuit, not a cooling fault.

Clearing codes and entering test mode

Most Whirlpool refrigerators clear a stored code by cycling power at the breaker for a minute, and many allow a diagnostic test mode by pressing a sequence of buttons on the display — the sequence differs per platform and is printed on the tech sheet. Test mode is very useful: it forces each fan, the damper and the defrost heater in turn, which tells you in two minutes whether a part is alive.

Unplug or isolate at the breaker before removing a panel, and never chip ice off the evaporator. The refrigerant lines are directly behind the coil. Sealed-system and inverter work belongs to a qualified technician.

Protecting the food

Keep the doors shut while you read the code and find the tech sheet. Move high-risk items into the compartment that is still cold, and discard anything that has been warm for over two hours. A refrigerator fault is a food-safety event first and a repair second.

Repair or replace

Fans, dampers, thermistors and defrost heaters are moderate parts. A compressor or a sealed-system leak is the expensive category, and the decision there depends on the cabinet's age and condition rather than on the code. Repair or replace explains the comparison; fridge warm and freezer cold handles the machine that shows nothing at all.

Frequently asked questions

Is PO dangerous?

No. It records a power loss. It matters only if it repeats, because repeated power loss suggests a supply or connection problem that will eventually damage the control.

Why does my code list not match this page?

Because Whirlpool uses several control platforms across brands and years. The tech sheet for your model is the only complete list, and this page gives the pattern the codes follow.

Can a Whirlpool fridge show a code and still be fine?

Yes — a stored code can remain after a transient fault. Clear it and check temperatures with a thermometer over 24 hours.

Sources

  1. Whirlpool Support — refrigerator error code guidance and tech-sheet location (whirlpool.com support sections), accessed 16 November 2026.
  2. Whirlpool service documentation for the P, F and E code families and diagnostic test mode.
  3. Editorial review against the parts trade: evaporator fan, damper and defrost failure patterns.

General information only. Code definitions are platform-specific and are confirmed by the tech sheet for your model. Unplug before interior work, and leave sealed-system work to a qualified technician.