Appliance Error Code Guide Codes, causes & fix order
Refrigerators · LG

LG Refrigerator Error Codes (Er codes)

An LG refrigerator that shows Er and two letters is naming a part, not a symptom: FF and RF are the two evaporator fans, IF is the ice room, DH is defrost, CO is the signal between boards.

Checked against LG support documentation Updated 16 November 2026 9 min read

The short answer

  • Er FF — freezer fan. Freezer warms, then the fridge follows.
  • Er RF — fridge fan. Fridge warms, freezer keeps freezing.
  • Er IF — ice-room fan. No ice, frost in the ice bucket.
  • Er DH — defrost heater. Ice builds on the evaporator; the fridge warms every few days.
  • Er CO — communication between boards. Check connectors before parts.

Decoding the letters

LG's refrigerator codes are abbreviated component names. Once you read them that way, an Er code tells you exactly which part of the cabinet to inspect:

CodeStands forWhat it monitorsWhat you will notice
Er FFFreezer fanRotation feedback from the freezer evaporator fanFreezer too warm, ice cream soft, frost on the coil
Er RFRefrigerator fanRotation feedback from the fridge evaporator fanFridge warm, freezer normal
Er IFIce fanIce-room fan / ice maker airflowNo ice, wet or frozen clumps in the bucket
Er DHDefrost heaterHeater continuity and defrost temperatureHeavy ice, fridge warms every few days
Er COCommunicationSignal between the main and display boardsDisplay blank or erratic, other codes appearing together

LG has used other Er pairs across platforms and years, and some models show a numeric code instead. Where your display differs, the manual's code page for your model is authoritative and the diagnostic order below still applies.

Fan codes: FF, RF, IF

All three fans do the same job in different places: move air over an evaporator and into a compartment. A fan fault almost always comes with ice, because the moment airflow stops, the coil ices and the ice then holds the blade.

  1. Listen at the compartment. Open the door, hold the door switch closed, and listen. A silent fan or a ticking blade is the clue; a fan running normally means the fault is in the feedback signal rather than the motor.
  2. Look at the evaporator. Remove the cover and inspect the coil. A solid block of ice means the defrost system, and the fan code is secondary.
  3. Clear the blade by hand. Ice, packaging or a displaced blade can stop rotation. If it turns freely after clearing, run the fridge and watch whether the code returns.
  4. Check the connector. The fan plug sits in a cold, damp place. Green corrosion or a loose pin produces a code with a healthy motor.
  5. Replace the motor if it has supply and does not turn.

Er DH: the defrost heater

Defrost runs a heater for a short period every several hours. When it fails, frost accumulates until airflow is blocked, so the pattern is a fridge that works, then warms, then works again after you empty and defrost it manually.

The parts are the heater, its thermal fuse on some models, the defrost sensor, and the relay on the board. A continuity test on the heater and fuse is the first step, done with the fridge unplugged.

Er CO: communication

Er CO means the boards are not talking. Before ordering a board, reseat every connector you can reach, look for water tracks or corrosion in the door hinge area (where the display harness passes), and check whether a recent power surge or lightning strike is plausible. Communication faults on fridges are often a harness, not a board.

Unplug before removing interior covers, and never chip ice with a sharp tool. Refrigerant lines run directly behind the evaporator. Sealed-system and inverter board work needs a qualified technician.

While you wait for a part

Move meat, dairy and leftovers into the compartment that is still cold, or into a cool box. Keep doors closed between checks. A fridge held shut with a fan fault will keep temperature far longer than one being opened every ten minutes to see whether it is fixed.

Repair or replace

Fans, sensors and defrost heaters are moderate parts and worth replacing on a fridge under about ten years old. Compressor or sealed-system faults are the expensive category; the decision there depends on age and on the cost of the food you would lose. Repair or replace lays out the comparison without invented prices.

Frequently asked questions

Why do I get two Er codes at once?

Because one fault causes another: a defrost failure ices the evaporator, the fan then stalls, and both the defrost and fan codes appear. Fix the defrost first.

Is Er IF worth repairing?

If you use the ice maker, yes — the part is small. If not, the ice-room fan can be ignored for a while, but frost in the ice room will eventually affect the freezer.

Can a fridge show Er codes and still be safe to use?

Only if both food compartments are holding temperature. Check with a fridge thermometer rather than by feel.

Sources

  1. LG Support — refrigerator error code guidance and troubleshooting for Er codes (lg.com support sections), accessed 16 November 2026.
  2. LG service documentation on evaporator fans, the defrost circuit and board communication.
  3. Editorial review against the parts trade: fan motor and defrost failure patterns in LG French-door and side-by-side cabinets.

General information only. Er code definitions and part locations vary by LG refrigerator platform and model year. Confirm against your model's manual and leave sealed-system work to a qualified technician.